10/16/2021 0 Comments Linux For G4 Mac Usb
Assuming, this is the only USB device you are using, go into open firmware and type the.USB to I2C/SPI/CAN Adapter Support Windows/Linux/MAC/Android/Raspberry Pi. Mengjay 10x G4 COB Bulb, LED G4 Crystal Light Bulbs, AC 12V 5W Bi-pin Base.From this point on, you should read 'Mac Mini' as 'G4 Mac Mini'. There is no further discussion of the Intel based Mac Minis on this page. Apple's first generation Mac Mini is something which a lot of Linux users have been waiting for: An inexpensive, readily available PowerPC system in a small, quiet and attractive chassis.With a Mac, you can accomplish the same thing with another hard drive set. When you downloaded Ubuntu for PowerPC, did you use Disk Utility to copy the image to the USB thumbdrive You should not be selecting any compression schemes at all.
Linux For G4 Usb Install Gives Firefox9.2 System Bus0000:00:0b.0 Host bridge: Apple Computer Inc. Installing Debian GNU/Linux on a iBook 3.3 (G4): Discovering the iBook G4 Next Previous ContentsApple technical specifications can be found there:Motherboard : PowerBook6,3 MacRISC3 Power Macintosh(There also exist at 800Mhz and 1Ghz) OptimizationsIf you feel gentoo-like you may want to install apt-buildI found this -mpowerpc-gfxopt -mcpu=7450 -mtune=7450 -maltivec -mabi=altivec -O2In /proc/sys/cpu/0/, you will find the current (speed) frequency, as well as the extreme values (speed-min / speed-max).In my case speed-min is set at 707000 and speed-max at 931840. A minimal install gives Firefox and business type apps in under 512Mb With room to store your own files too.Specifically the Puppy Bruno 2 has been able to run on desktops, and laptops alike. It even ran better (finding the USB Broadband modem) on the Eee PC than PuppEee which was designed for that platform.It can be run from a CDROM, HD, or USB flash drive. My 8Gb Flash drive with Puppy Bruno 2 has Open Office, qbitorrent, complete 'rescue ware', and a full multimedia suite. Almost all music, files, and video formats run natively.The operating system AND my apps all fit in 1gb, MAX.KeyLargo/Intrepid USB0001:01:1b.0 USB Controller: NEC Corporation USB (rev 43)0001:01:1b.1 USB Controller: NEC Corporation USB (rev 43)0001:01:1b.2 USB Controller: NEC Corporation USB 2.0 (rev 04)0002:02:0b.0 Host bridge: Apple Computer Inc. KeyLargo/Intrepid USB0001:01:1a.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB0001:01:19.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid Mac I/O0001:01:18.0 USB Controller: Apple Computer Inc. UniNorth 2 PCI0001:01:17.0 ff00: Apple Computer Inc. ![]() Other macintosh's fan driversAirport Extreme cards are not supported yet, because Broadcom does not want to help the creation of a new driver, there are several projects, not only for macs, to reverse-engineer it or to use the windows one using an emulation layer.Since one can run macosx things under linux (seeMOL), doing NAT with Macosx could maybe work. It adds 1 to the loadAverage, however it uses very little CPU. Actually your cpu is notYes, that's due to the TASK_UNINTERRUPTIBLE flag. 9.8 Hard Drive Informations30/40/60GB according to the model, Ultra ATA.Powers-up in standby SET FEATURES subcmd spins-up.WARNING: Following data may be incorrect.Device size with M = 1024*1024: 2107703808 MBytesDevice size with M = 1000*1000: 2210087628 MBytes (2210087 GB)R/W multiple sector transfer: Max = 128 Current = ?Advanced power management level: unknown setting (0x8040)Recommended acoustic management value: 254, current value: 128You can at any moment check the temperature given by the sensor in your hard drive:WARNING: Drive /dev/hda doesn't appear in the database of supported drivesWARNING: But using a common value, it reports something.WARNING: Note that the temperature shown could be wrong.WARNING: See -help, -debug and -drivebase options.WARNING: And don't forget you can add your drive to hddtemp.db/dev/hda: Hitachi IC25N040ATMR04-0: 33 C or FThe temperature at which the fan starts are controlled by therm_adt7467You might notice that it increases load statistics :11:27:37 up 32 min, 1 user, load average: 1.96, 1.23, 0.7711:37:15 up 42 min, 1 user, load average: 0.11, 0.56, 0.65>This is just an artefact due to the way kernel counts daemonized>module cpu usage in the load average. Reconfiguring the console keymapI do not seem to be able to adapt to a one-button mouse, at least not under linux, but there is an emulation, which we will directly add it to /etc/sysctl.conf () so that it will be enabled automatically.# /etc/sysctl.conf - Configuration file for setting system variablesThis map the apple key as a right click and the Fn apple key as a click from the middle button.The list of keycodes is in /usr/src/linux/include/linux/input.h.You can also get them by using the showkey command in console.
0 Comments
Leave a Reply. |
AuthorAustin ArchivesCategories |